EMG Muscle Sensor v3.0 Kit with Electrode Cable & 3 Pads (Arduino)
EMG Muscle Sensor v3.0 Kit with Electrode Cable & 3 Pads (Arduino)
Couldn't load pickup availability
Short Product Description
Short Product Description
This EMG Muscle Sensor v3.0 Kit enables microcontrollers like Arduino to measure, filter, and rectify muscle electrical activity for robotics and bionic control. Instead of outputting raw noisy EMG waveforms, the board delivers a smoothed 0 to +Vs analog voltage proportional to muscle contraction on its SIG pin. Powered by a dual ±3.5V to ±9V supply and equipped with an adjustable Gain potentiometer, the kit includes the sensor board, a 3-lead electrode cable, and three disposable surface electrodes.
Key Features
Key Features
- Rectified Analog Output: Outputs a smoothed 0 to +Vs DC voltage proportional to muscle contraction intensity, simplifying Arduino analogRead() code.
- Adjustable Gain Control: Onboard SMD trimmer potentiometer lets you fine-tune sensitivity for small or large muscle groups.
- Dual Power Supply Architecture: Supports ±3.5V to ±9V bipolar DC input (+Vs, GND, -Vs) for stable differential amplification.
- Breadboard-Ready Headers: Pre-soldered 3-pin power and 2-pin signal headers plug cleanly into breadboards or DuPont cables.
- Complete Prototyping Kit: Includes the Muscle Sensor v3.0 board, a 3.5mm 3-lead snap electrode cable, and 3 disposable EMG/ECG pads.
Full Product Description
Full Product Description
Filtered and Rectified Analog EMG Output for Microcontrollers
The Muscle Sensor v3.0 board processes weak bioelectric signals from skeletal muscles into an easy-to-read 0 to +Vs analog voltage. Because the onboard circuitry amplifies, rectifies, and smooths the electromyography (EMG) signal internally, your microcontroller can read muscle flexing intensity directly via a standard ANALOG IN pin (SIG and GND). Pre-soldered 2.54mm male headers on the underside allow quick insertion into a solderless breadboard or direct connection with female jumper wires.
Complete 3-Lead Cable & Disposable Electrode Kit
Every kit comes ready for bench prototyping with one Muscle Sensor v3.0 PCB, one 3.5mm plug 3-lead EMG cable (color-coded red, yellow, and blue snap leads for active, reference, and ground placement), and three disposable surface electrode pads. An onboard Gain trimmer potentiometer lets you tune amplification sensitivity to match different muscle groups such as forearms or biceps. Note that this is strictly an electronic development module for experienced Arduino/MCU makers, not a consumer or medical product.
Technician Tip
Ensure you supply a true bipolar dual power source (+Vs, GND, -Vs, minimum ±3.5V, typically two 9V batteries in series as shown in the wiring diagram) rather than a single 0–5V pin, or the op-amp stage will not operate properly. Our technicians at Sun Cheong also recommend checking the SIG output voltage with a multimeter and dialing down the Gain potentiometer before connecting to a 3.3V (ESP32) or 5V (Arduino) analog pin, as strong flexes powered by ±9V can push SIG above 5V and risk damaging your ADC input.
Technical Specifications
Technical Specifications
- Model / Silkscreen: Muscle Sensor v3.0
- Measurement Type: Surface Electromyography (EMG) — Filtered & Rectified Analog Output
- Power Supply: Dual Bipolar DC Supply (±3.5V min to ±9V typical via +Vs, GND, -Vs)
- Output Signal: Analog Voltage (0 to +Vs on SIG / GND)
- Sensitivity Adjustment: Onboard Gain trimmer potentiometer
- Electrode Interface: 3.5mm TRS jack for 3-lead EMG cable
- Package Contents: 1x Muscle Sensor v3.0 Board, 1x 3-Lead EMG Cable, 3x Disposable Surface Electrodes
- Usage Restriction: Developer / educational prototyping module only (not a medical or consumer device)
Delivery Options
Delivery Options
- Local delivery within Hong Kong and in-store pickup.
- Free shipping for orders of HK$400 or above; HK$35 shipping fee for orders below HK$400.
- Shipped by SF Express, usually dispatched the same day for orders confirmed before 6:00 PM (Mon–Sat).
- Estimated delivery time: 1–3 business days after dispatch (Hong Kong).
- In-store pickup details (location and time) will be confirmed by email or phone message.
- Delivery times are estimates and may be affected by weather or unforeseen circumstances.
FAQ Section
FAQ Section
- Can I power the Muscle Sensor v3.0 from a single 5V Arduino pin without -Vs?No, this board requires a dual bipolar power supply (+Vs, GND, and -Vs, minimum ±3.5V to ±9V typical) such as two 9V batteries wired in series to operate correctly.
- Is this EMG muscle sensor kit certified for medical diagnosis or clinical healthcare use?No, this kit is strictly an educational and electronics development module intended for experienced microcontroller users, not a medical or consumer health product.
- How should the three disposable electrode snaps be placed on the muscle?Snap the two active/mid-muscle leads onto pads placed along the target muscle belly (such as the bicep or forearm) and attach the third reference/ground pad to a bony or inactive area nearby such as the elbow.
- Can I pick up replacement 9V battery snap clips or DuPont wires at your Sham Shui Po store?Yes, you can pick up this EMG sensor kit along with 9V battery snap connectors, breadboards, and DuPont cables at our Sham Shui Po shop (新昌電腦有限公司), though please check in-store for spare pad availability.
- Can I connect the SIG output directly to a 3.3V ESP32 analog pin when powered by ±9V batteries?You should use a voltage divider or lower the Gain and supply voltage (such as ±5V) while verifying SIG with a multimeter first, because SIG can output up to +Vs volts and exceed a 3.3V ADC limit.
Target Users / Applications
Target Users / Applications
- University engineering students and makers building EMG-controlled robotic arms, bionic hands, or prosthetic prototypes with Arduino.
- Biomechanics and STEM classrooms demonstrating bioelectric muscle signal acquisition and analog filtering.
- Interactive installation developers creating gesture- or muscle-flex-triggered controllers.
