Skip to product information
1 of 2

3S 11.1V 100A Peak Li-ion BMS Protection Board w/ Balance (12.6V)

3S 11.1V 100A Peak Li-ion BMS Protection Board w/ Balance (12.6V)

🔥 1 sold•✓ In stock
Regular price HK$35.00
Regular price Sale price HK$35.00
Sale Sold out
Shipping calculated at checkout.
Quantity

Short Product Description

This 3S 11.1V (12.6V max) BMS protection board is built for 3.6V/3.7V lithium-polymer and ternary Li-ion battery packs. Powered by the BM3451 IC and 15 low-resistance MOSFETs, it provides overcharge, over-discharge, short-circuit, wire-break protection, and passive hardware balancing. Measuring 6.1 x 4.2cm, it supports ~50–60A (same-port) or ~70–80A (split-port) continuous current—and up to 100A with copper busbar reinforcement—ideal for power tools, e-scooters, and portable power stations.

Key Features

  • 3S 11.1V Li-ion / Li-Po Support: Built strictly for 3-series 3.6V/3.7V ternary lithium and polymer cells (12.6V full charge).
  • 15 Low-Resistance MOSFETs + BM3451: Individual MOSFET resistance as low as 3mΩ paired with the BM3451 protection IC and wire-break detection.
  • Flexible Same-Port / Split-Port Output: Delivers ~50–60A continuous in same-port mode (C-), ~70–80A in split-port mode (P-/C-), or up to 100A with reinforced copper busbars.
  • Hardware Cell Balancing: Built-in resistor balancing equalizes voltage differences across cells during charging without excessive heat.
  • Pre-Configured 3S Balance Pads: B1 and B2 feature factory 0-ohm jumpers for direct 3S wiring via B-, B3, B4, and B+.

Full Product Description

3S 11.1V High-Current Protection with Hardware Cell Balancing

Engineered specifically for 3-series (3S) 3.6V/3.7V lithium-ion, lithium-polymer, LiCoO₂, and LiMn₂O₄ battery packs (not compatible with 3.2V LiFePO₄), this 6.1 × 4.2cm (14.5g) BMS board uses a dedicated BM3451 protection IC, 15 KND3203B MOSFETs (individual MOS resistance down to 3mΩ), and four R003 shunt resistors. It protects against overcharge, over-discharge, overcurrent, short circuits, and balance-wire disconnection, while hardware resistor balancing equalizes cell voltages during charging to preserve pack longevity.

Same-Port / Split-Port Wiring & 100A Copper Reinforcement

The board supports both Same-Port (charger - and load - both wired to C-, rated ~50–60A continuous / ~600W) and Split-Port (charger - to C-, load - to P-, rated ~70–80A continuous / ~800W) configurations. For sustained loads above 50A up to 100A continuous, solder extra 1.5mm² to 2.5mm² copper wires along the exposed tinned busbars on the front and rear of the PCB to minimize trace heating and voltage drop.

Technician Tip

Pay strict attention to the physical 3S balance pad layout on this board and your charger selection before applying power. On this physical OSKJ board, B1 and B2 are already factory-bridged with 0-ohm SMD jumpers to B-—so you must wire your 3-cell pack's negative terminal to B-, and the three cell positives sequentially to B3 (Cell 1+), B4 (Cell 2+), and B+ (Cell 3+ / Pack+). Our technicians at Sun Cheong also warn to use only a dedicated 12.6V lithium charger (3 × 4.2V, standard rate ~0.2C) and never a 12V lead-acid charger, whose high voltage can puncture the MOSFETs and disable overcharge protection; also expect the onboard indicator LEDs to remain OFF when cells are balanced and full, lighting up only when passive balancing is active or if miswired.

Technical Specifications

  • Supported Battery Chemistry: 3S 3.6V/3.7V Polymer / Ternary Li-ion (11.1V nominal, 12.6V full charge; NOT for 3.2V LiFePO₄)
  • Protection IC & MOSFETs: BM3451 IC, 15x KIA KND3203B MOSFETs (3mΩ single MOS), 4x R003 shunt resistors
  • Continuous Current (Bare PCB): Same-Port (C-): ~50–60A (~600W) / Split-Port (P-/C-): ~70–80A (~800W)
  • Maximum Current (Reinforced): Up to 100A (Requires soldering 1.5–2.5mm² copper wires onto PCB busbars for >50A continuous loads)
  • Recommended Charger: Dedicated 12.6V Lithium Battery Charger (0.2C standard rate; NO lead-acid chargers)
  • 3S Balance Pinout (Physical Board): Pack- to B- (B1/B2 factory-jumpered via 0Ω); Cell 1+ to B3; Cell 2+ to B4; Cell 3+ (Pack+) to B+
  • Terminals: B- (Battery -), C- (Charger -), P- (Load - in Split-Port mode)
  • Protection & Balancing: Overcharge, Over-discharge, Overcurrent, Short-circuit, Wire-break protection, Hardware Balancing
  • Dimensions: 6.1cm x 4.2cm (61mm x 42mm)
  • Weight: 14.5g

Delivery Options

  • Local delivery within Hong Kong and in-store pickup.​
  • Free shipping for orders of HK$400 or above; HK$35 shipping fee for orders below HK$400.​
  • Shipped by SF Express, usually dispatched the same day for orders confirmed before 6:00 PM (Mon–Sat).​
  • Estimated delivery time: 1–3 business days after dispatch (Hong Kong).​
  • In-store pickup details (location and time) will be confirmed by email or phone message.​
  • Delivery times are estimates and may be affected by weather or unforeseen circumstances.​

FAQ Section

  • Can I use this 3S 11.1V BMS board with 3.2V LiFePO4 battery cells?No, this board is configured specifically for 3S 3.6V/3.7V lithium-polymer and ternary Li-ion cells (11.1V nominal, 12.6V max) and is not suitable for 3.2V LiFePO4 batteries.
  • Which balance pads should I wire for a 3S battery pack on this physical board?On this physical board (where B1 and B2 already have factory 0-ohm jumpers soldered), wire Pack- to B-, Cell 1+ to B3, Cell 2+ to B4, and Cell 3+ (Pack+) to B+.
  • Why do the onboard LEDs stay off even when my 3S lithium battery is fully charged?The onboard LEDs only light up when the board is actively balancing an imbalanced cell or when wired incorrectly, so the lights remain off when all three cells are balanced and full.
  • Can I pick up this 3S 100A BMS board along with heavy-gauge silicone wire and solder at your Sham Shui Po store?Yes, you can pick up this 3S BMS board alongside 1.5–2.5mm² copper busbar wire, XT60/XT90 connectors, and solder at our Sham Shui Po shop (新昌電腦有限公司).
  • Do I need to solder extra copper wires to draw 80A to 100A continuously?Yes, while the bare PCB handles ~50–60A (same-port) or ~70–80A (split-port), continuous current above 50A up to 100A requires soldering extra 1.5–2.5mm² copper wires along the front and back tinned busbars.

Target Users / Applications

  • DIY battery builders assembling 3S 11.1V (12.6V) 18650 or Li-Po packs for cordless drills, impact wrenches, and portable power tools.
  • Robotics and RC hobbyists building high-discharge 3S power packs for robots, solar backup boxes, or portable inverters.
  • Technicians replacing failed BMS boards inside 11.1V–12.6V lithium battery packs (matched to 3.7V chemistry).
View full details